Standard radiator sizes in the UK: heights, widths and panel types
UK panel radiators are sold in a fairly small set of heights, a long run of widths and four or five panel types. This page shows you what those standard sizes are, how to read a size code like 600 x 1000 Type 22, and how to choose a size for a given wall. Pipe centres and valve fitting are covered on the main page. Here we deal with the radiator body itself: height, width, depth and output. Sizes vary a little between makers, so always check the maker's data sheet before you order.
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Our picks
Type 22 double panel double convector radiator, white
Gives the most heat for a given height and width among the common types. You can often go one width or one height smaller than with a Type 11 and keep similar output. Always check the maker's output table.
View on AmazonAdType 21 double panel single convector radiator
A middle option on depth and output. Useful when the radiator sits close to a door or furniture.
View on AmazonAdType 11 single panel convector radiator
Slim and light. It's a good replacement for an older single panel radiator when output is enough.
View on AmazonAdStelrad Softline radiator
Stelrad is a long established UK maker. Their data sheets list sizes, types, outputs and dimensions in one place, which makes comparing easy. Check which Type and size you are looking at.
View on AmazonAdRadiator wall brackets, heavy duty
New radiators come with brackets, but a replacement is often a different size from the old one. Spare brackets help when one of the old fixings doesn't suit the new radiator or the wall. Match the bracket to the radiator type and weight.
View on AmazonAdLaser distance measure
Helps you get height and width right before you pick a size. A tape measure works just as well if you check twice.
View on AmazonAdCommon buying mistakes
- Choosing by size alone and ignoring output. Two radiators with the same height and width can give very different heat.
- Swapping a Type 11 for a Type 22 without checking depth, door swing and furniture.
- Comparing output figures quoted at different Delta T values.
- Assuming every range offers every width. Check the maker's list before you finalise the calculation.
- Forgetting clearance below and above the radiator, which affects airflow and how well it heats.
- Measuring with the old radiator's brackets or valves included and treating that as the body size.
How do I read a radiator size code?
A code such as 600 x 1000 Type 22 gives height first, then width, then panel type. Both measurements are for the radiator body only. Valves, tails and brackets are not included. Some retailers write width first, so check the product drawing if you aren't sure. Output is listed separately and is not part of the size code.
Which height should I choose?
Take the space between floor and sill, leave the clearance the maker asks for, and pick the largest standard height that fits. 600 mm is a very common height. 300 to 450 mm radiators suit under low windows or in bathrooms. 700 mm and above is useful where wall width is short and you need output from height instead. If you cannot fit the old height, you can often keep the output by choosing a wider radiator or a deeper type.
Type 11, 21 or 22: what changes?
Each step up adds a panel or a set of convector fins. That raises the output for the same height and width and also adds depth and weight. Type 22 is the usual choice for main rooms. Type 11 is common in tight spaces. Compare the actual output table, since the gain depends on the range and the size.
How do I match the output of my old radiator?
Look for a label or model name on the old radiator, or work out its size and type and find the maker's table. Pick a new radiator with equal or higher output at the same Delta T. If the room was never warm enough, going up in output is sensible. This page does not cover heat loss calculations. For a full room by room calculation, ask a heating installer.
Do I need bigger radiators with a heat pump or low flow temperature?
Yes, often. Radiator output falls as the water temperature falls, so a radiator that works with a boiler at higher flow temperatures may give much less heat at low flow temperature. Output tables at lower Delta T values show this. If your system is changing, get the room heat losses and radiator sizes checked by a qualified installer before you buy.
What about fixing the radiator to the wall?
A filled radiator is heavy, and larger Type 22 and Type 33 sizes weigh more again. Fix brackets into masonry with suitable plugs, or into studs on a stud wall, following the maker's instructions. Use the number of brackets the maker specifies for the width and height.
FAQ
What is the most common radiator size in the UK?
There is no single official standard, but 600 mm high is among the most common heights, and Type 22 is a very common type for main rooms. Common widths range from 400 mm to 2000 mm. Sizes differ slightly by maker.
What are the standard radiator heights?
Common heights are 300, 400, 450, 500, 600 and 700 mm. Some ranges also offer 900 mm. Check the range you want, since not every maker sells every height.
Does radiator size mean output?
No. Size is the physical height, width and depth. Output depends on the type, the size and the water temperature. Always check the maker's output table.
What is the difference between Type 11 and Type 22?
Type 11 is a single panel with one set of convector fins. Type 22 has two panels and two sets of fins. For the same height and width, Type 22 gives more output and is deeper.
How do I convert BTU/h to watts?
Divide the BTU/h figure by 3.412 to get watts. Multiply watts by 3.412 to get BTU/h.
Can I fit a bigger radiator than the old one?
Often yes, if the wall, sill and pipework allow. Check the height and width, the depth, the brackets and the pipe centres. See the main page for the pipe checks.
Are radiator sizes in mm or inches?
Modern UK radiators are sold in millimetres. Older radiators were often made in imperial sizes, which is why they can be hard to match with metric ones.
More guides
- Radiator pipe centres size guide UK: how to measure and match
- How to Measure Radiator Pipe Centres
- Radiator wall distance: how to measure it and what to do with the number
- Radiator valve spacing check for UK replacements
- Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 700mm high radiators in the UK: widths, clearances and fit
- 400mm high radiators in the UK: which width and type fits