Radiator wall distance: how to measure it and what to do with the number
Wall distance is the figure people most often get wrong when they swap a radiator. It is the gap between the wall and the centre of the pipe, and it decides whether the new valves line up without bending pipes. This page shows how to take the measurement properly, how to deal with skirting boards and uneven pipes, and what to buy if the numbers don't match. It covers measuring and fitting only. For pipe centres and body width, use the main size check page.
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Our picks
Solid chrome radiator extension tails, 1/2 in BSP
Takes up a small gap without bending the pipe. Fit one per side so the valves stay level.
View on AmazonAdFlexible radiator connector, 15 mm
Absorbs minor misalignment where a rigid tail would put strain on the joint. Not a cure for large gaps.
View on AmazonAdCorner radiator valve pair, 15 mm
Turns the connection through 90 degrees so the radiator hangs without moving the pipework.
View on AmazonAdTelescopic radiator valve extension
Adjustable length makes it easier to correct a gap you cannot measure exactly in advance.
View on AmazonAdFolding rule or small steel engineer's square
A rigid edge pressed flat to the wall gives a more reliable reading than a floppy tape, especially behind skirting.
View on AmazonAdThread sealing cord or PTFE tape for radiator tails
Needed to seal the tail thread. Cord is more forgiving if you have to adjust the tail position.
View on AmazonAdCommon buying mistakes
- Measuring to the outside of the pipe and forgetting to add half the pipe diameter.
- Measuring at the valve body instead of the pipe or tail centre.
- Measuring only one side and assuming the other pipe matches.
- Ignoring the skirting board until the radiator is on the brackets.
- Measuring from the old radiator's front face instead of the wall.
- Stacking several tails on one side to fill a large gap, which weakens the joint and looks untidy.
What exactly is wall distance on a radiator?
It is the distance from the finished wall surface to the centre line of the pipe or valve tail. On the radiator side, the equivalent figure is the distance from the wall to the centre of the tapping. Makers publish it in their technical drawings, often separately for the bracket settings. Compare like with like: pipe centre to tapping centre.
How do I measure it with the old radiator still on?
Close both valves and look at where the old radiator sits. Measure from the wall to the centre of the valve tail or the pipe just below the valve. If the old radiator hangs level and the valves sit square, that distance is a good reference. Note it down for left and right.
What about the skirting board?
Measure wall distance from the wall surface, not from the skirting board face. Then check that the radiator back, brackets and valve body clear the board. Many installers set the radiator high enough to pass over the board, or cut a small notch. Leave enough gap under the radiator for the valves and for cleaning, and check the maker's minimum clearance.
What if the new radiator has a different panel type?
A different type usually means a different depth, so the tapping sits at a different distance from the wall. A double convector sits further out than a single panel. Adjust with the bracket setting where the maker allows it, or use a tail. Large differences are better solved by choosing a panel type that fits the pipes.
When should I move the pipes instead of using tails?
If the gap needs more than a short tail, or if the pipes are very uneven, bending or re-routing is the cleaner fix. Pipework changes mean draining the system. If you are not confident doing that, ask a plumber. Heating work on gas boilers must be done by a Gas Safe registered engineer.
FAQ
Is wall distance measured to the pipe edge or the centre?
To the centre. Measure to the nearest edge and add half the pipe diameter. For 15 mm pipe, add 7.5 mm.
Can I fix a wall distance mismatch with a flexible connector?
Only for small differences of a few millimetres. For bigger gaps use a solid tail or change the pipework.
Does the skirting board change the wall distance?
No, the distance is from the wall surface. But the board can block the radiator or valve, so check clearance.
What if the left and right pipes are at different distances?
A small difference can be absorbed by a flexible connector or a short tail on one side. A large difference means the pipes need adjusting.
Do I need to drain the system to measure?
No. Measuring needs no draining. Draining is only needed once you remove the old radiator or change pipework.
Where do I find the wall distance for the new radiator?
In the manufacturer's technical drawing or installation sheet for your model. If it is missing, ask the retailer before you order.
More guides
- Radiator pipe centres size guide UK: how to measure and match
- How to Measure Radiator Pipe Centres
- Radiator valve spacing check for UK replacements
- Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
- Standard radiator sizes in the UK: heights, widths and panel types
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 700mm high radiators in the UK: widths, clearances and fit
- 400mm high radiators in the UK: which width and type fits