400mm high radiators in the UK: which width and type fits
A 400mm high radiator is usually chosen because something limits the height: a low window sill, a shelf, a stair wall or a cloakroom. This page helps you pick the width and panel type for that space. It also covers what changes at 400mm compared with taller sizes. Read the table, then check the maker's drawing for the exact depth, tapping centres and output before you order. We cover sizing and fitting, not gas work or full heat loss calculations.
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Our picks
400mm high single panel convector radiator (Type 11)
The slimmest of the common panel types. Output per width is lower, so choose a wider unit if the wall allows.
View on AmazonAd400mm high double panel double convector radiator (Type 22)
More output from the same height and width than Type 11. Deeper, so check the wall space and pipe distance.
View on AmazonAd400mm high Type 21 (P+) radiator
Sits between the two in output and depth. Not every range offers it at 400mm.
View on AmazonAdChrome radiator extension tails, 1/2 in BSP
Closes small gaps per side without moving the pipework.
View on AmazonAdCorner radiator valves, 15mm
Make the connection easier where angled valves do not line up.
View on AmazonAdCommon buying mistakes
- Ordering a 400mm radiator without checking that the range actually offers your width at that height.
- Measuring the old radiator's height instead of the available space under the sill or shelf.
- Choosing Type 22 without checking the extra depth and the new wall to pipe distance.
- Assuming a wider radiator always fits. Valve space on both sides still has to be deducted.
- Comparing radiators by size only and ignoring the output table at Delta T50.
- Boxing a low radiator in a closed cover and then wondering about the lower output.
Which widths are common for 400mm high radiators?
Widths usually run from about 400mm up to 2000mm or more, in steps of 100 to 200mm. The exact list depends on the range. Do not assume every width exists at 400mm high, because some ranges skip it. Check the maker's size chart for your range.
How much heat does a 400mm radiator give?
Output depends on width, panel type and the range. A Type 22 gives more than a Type 11 of the same size. We do not quote a figure here because it varies by maker. Use the output table in watts or BTU/h at Delta T50 and compare it with your room's heat loss.
Does a 400mm radiator fit under a window?
Often yes, but measure first. Allow space below for the valve pipework and brackets and above for air flow. Many installation sheets give minimum gaps. Take the figure from the sheet for your radiator, then measure from the floor to the sill.
Will a taller or shorter radiator change my pipe positions?
Usually not much. The tappings are at the bottom of the radiator, so changing height mostly changes the top edge. Width, panel depth and bracket position matter more. Use the table on the main page to check pipe centres and wall to pipe distance.
Should I choose Type 11, Type 21 or Type 22?
Pick by depth and output. Type 11 is slim but gives the least heat. Type 22 gives the most but needs the most depth. Type 21 is a middle option. If height is fixed and depth is free, Type 22 is the common answer. If depth is limited, go wider instead.
FAQ
Is 400mm a standard radiator height in the UK?
It is a common height, but not every range offers it. Many ranges use 300, 450, 500, 600 and 700mm. Check the range's size chart before you plan around 400mm.
Can I swap a 450mm radiator for a 400mm one?
Often yes if the width and type match and the pipes line up. Output will be lower, so compare the figures and consider a wider radiator.
What is the difference between Type 11 and Type 22 at 400mm?
Type 11 has one panel and one convector fin set. Type 22 has two panels and two fin sets. Type 22 gives more output and is deeper.
Do I need to drain the system to fit a new radiator?
Normally yes, unless you can isolate the radiator and it has working valves on both sides. If you are unsure, ask a heating engineer. Work on the boiler or gas supply is for a Gas Safe registered engineer.
How far from the floor should a 400mm radiator sit?
Follow the maker's installation sheet. It gives the minimum gaps below and above. Measure your space and check it against those figures.
More guides
- Radiator pipe centres size guide UK: how to measure and match
- How to Measure Radiator Pipe Centres
- Radiator wall distance: how to measure it and what to do with the number
- Radiator valve spacing check for UK replacements
- Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
- Standard radiator sizes in the UK: heights, widths and panel types
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 700mm high radiators in the UK: widths, clearances and fit