How to Measure Radiator Pipe Centres
Pipe centres are the distance from the middle of one pipe to the middle of the other, measured sideways where the pipes meet the radiator valves. Get this figure right and the rest of the size check is simple. You need a tape measure, a pencil and about ten minutes. The measuring does not need any draining or pipework. Below you will find three ways to take the measurement, the other figures worth noting at the same time, and the slips that most often lead to a radiator that does not line up.
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Our picks
Digital vernier calliper, 150 mm
Gives the pipe outside diameter to the nearest tenth of a millimetre. You also need that figure for Method B and Method C.
View on AmazonAdSteel tape measure, 5 m, with a stiff blade
A stiff blade stays straight along the wall. The hook end helps when you measure from a wall or skirting.
View on AmazonAdSpirit level, 300 to 600 mm
A short level fits behind a radiator and between pipes. It shows lean before you buy tails or valves.
View on AmazonAdSolid chrome radiator extension tails, 1/2 in BSP
Closes small gaps on each side. Use the pipe centres figure to work out how much extension is needed.
View on AmazonAdTelescopic radiator valve extension
Adjusts to the gap, so you need not cut a fixed tail. Handy if the two sides differ slightly.
View on AmazonAdCorner radiator valve pair, 15 mm
Angled valves will not fit wall pipes. Corner valves turn the connection to suit, so your wall distance figure matters.
View on AmazonAdCommon buying mistakes
- Measuring from the edge of the valve body instead of the pipe or the connection centre.
- Measuring along the skirting board or a sloping line instead of level.
- Forgetting to subtract (Method B) or add (Method C) the pipe diameter.
- Taking one measurement only. Take two and compare.
- Measuring the old radiator's width and assuming the pipe centres match it. They rarely do.
- Measuring floor to pipe centre before new flooring is laid, then finding the height is off.
What exactly are radiator pipe centres?
Pipe centres are the horizontal distance between the middle of the flow pipe and the middle of the return pipe at the radiator. Manufacturers also give tapping centres for the radiator itself. These are the distance between the middle of the two connection points on the radiator. When the two figures match, the radiator can go straight on. When they do not, tails or a different radiator can bridge the difference.
Which measuring method is most accurate?
Method B is usually best. Measure from the outer edge of one pipe to the outer edge of the other, then subtract one pipe diameter. Outer edges are easy to see and the tape sits cleanly against them. Estimating the middle of each pipe by eye is where most errors creep in. If you use Method A, mark the centre of each pipe with a pencil first.
Do I measure with the old radiator on or off?
Either works. With the radiator on, measure at the valves and check that the valve centre sits over the pipe. With it off, measure at the pipe ends. Do not drain or remove anything just to measure. If you plan to remove the old radiator, close both valves first, protect the floor and follow safe practice for heating systems. For gas appliances or boiler work, use a qualified engineer.
What if the two pipes are not at the same distance from the wall?
Measure each side on its own and write both figures down. A small difference may be absorbed by flexible fittings or by slightly angled tails. A bigger difference can strain the connections. In that case, speak to a plumber about adjusting the pipework before you fit the new radiator.
How do I turn my measurement into a radiator width?
Use the table and calculation on the main size check page. Take your pipe centres figure and compare it with the new radiator's tapping centres from the maker's drawing. The difference per side tells you whether the radiator fits as is, needs short tails, or is a poor match.
FAQ
Do I need to drain the system to measure pipe centres?
No. A tape measure is enough. You only need to drain down if you remove the old radiator, and that is a separate job.
Are pipe centres the same as the radiator width?
No. Pipe centres are the distance between the two pipes. Radiator width is the length of the body. The pipe centres figure is usually a little different from the width, and the maker's drawing shows how much.
Should I measure to the middle of the valve or the middle of the pipe?
Use the middle of the pipe where it enters the valve, or the middle of the valve connection. For angled valves the two are usually the same. If they are not, note both and tell your supplier.
What if I get two different figures?
Measure again, level and from the same points. If the figures still differ, a pipe may lean or the pipes may not be parallel. Note both and ask a plumber before you buy.
How accurate does the measurement need to be?
Aim for the nearest millimetre. Tails and telescopic extensions can take up small errors, but repeated mistakes add up across both sides.
Can I measure if the radiator is behind furniture?
Move the furniture if you can. You need to see both pipes and the wall behind them. A phone photo with the tape in frame helps you check the figure later.
More guides
- Radiator pipe centres size guide UK: how to measure and match
- Radiator wall distance: how to measure it and what to do with the number
- Radiator valve spacing check for UK replacements
- Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
- Standard radiator sizes in the UK: heights, widths and panel types
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 700mm high radiators in the UK: widths, clearances and fit
- 400mm high radiators in the UK: which width and type fits