700mm high radiators in the UK: widths, clearances and fit
A 700 mm high radiator is a good choice when you need more output than a 600 mm one but the wall width is limited. It is less common than 600 mm, so the first job is to check that your preferred width and panel type exist at this height. This page covers what is specific to 700 mm: clearance below and above, how it changes your pipe fit, how to choose the width and where it makes sense. For measuring pipe centres and wall distance, use the main size check page. We cover sizing and fitting only,
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
700 mm radiator check: does it fit your wall?
- How much vertical space do you have from floor to the underside of the windowsill or shelf?Measure at the exact spot. A 700 mm radiator needs its own height plus a gap underneath and above. Makers usually give minimum gaps in the instructions, so check these. As a rule of thumb, a gap of roughly 100 to 150 mm below and some clearance above for the top grille is common. Confirm with the ma
- Where are the pipes and valves in relation to the floor?On a like-for-like swap the bottom of the radiator is set by the existing pipes. A taller radiator grows upwards, not downwards. Measure from the floor to the pipe centre and compare it with the tapping height on the maker's drawing.
- What is your pipe centre distance, and what body width does it give you?Pipe centres minus the valve allowance on both sides gives the maximum body width. If you fall between standard widths, go down one size and close the gap with extension tails, as described on the main page.
- Which panel type and output do you need?Compare outputs from the maker's table at the same flow temperature. UK ratings are normally quoted at ΔT50. A 700 mm radiator gives more output than a 600 mm one of the same width and type, but the increase is not exactly proportional. Use the maker's table, not a calculation of your own.
Quick reference
| Situation | Why 700 mm can help | What to check |
|---|---|---|
| Replacing a 600 mm radiator and you need more output, but the width is fixed by | Gains output through height, so the width and pipe centres can stay the same | Space under the sill, and that the same width is offered at 700 mm in your panel |
| Narrow wall section, for example beside a door or between furniture | Gets more output from a short body width | Whether short widths are offered at this height, and the valve position |
| Radiator below a window | Can work if the sill is high enough | Gap above the radiator for airflow and for curtains or blinds that hang down |
| Hallway or landing with limited width | Gives output without a long radiator | Width of the walkway, and the depth of the panel type you choose |
| Room with low sills or a shelf above | Often not a good fit | Look at 600 mm or 500 mm in a wider body, or a Type 22 at a lower height |
| Pipes come from the ceiling or a different height | Not a given fit | Position of tappings against your pipework, and whether pipe changes are needed |
Our picks
Type 22 double panel convector radiator, 700 mm high
Two panels and two sets of convector fins give more output than a single panel of the same height and width. Check the wall-to-pipe distance first.
View on AmazonAdType 11 single panel convector radiator, 700 mm high
Slimmer than a Type 22 and often closer to older single panel radiators in depth. Output is lower, so check the table.
View on AmazonAdType 21 (P+) radiator, 700 mm high
Often a good match for pipes that sit around 55 to 65 mm from the wall. Always confirm against the drawing.
View on AmazonAdSolid chrome radiator extension tails, 1/2 in BSP
Closes the gap per side when you go down to the next standard width.
View on AmazonAdTelescopic radiator valve extension
Adjusts in length, so it is useful when the measurement is not exact. Make sure the joint is accessible and fully tightened.
View on AmazonAdRadiator bracket and fixing set for panel radiators
A taller, filled radiator is heavier. Use fixings suited to your wall and follow the maker's instructions for the number of brackets.
View on AmazonAdCommon buying mistakes
- Choosing a 700 mm radiator without checking whether your preferred width and panel type are made at that height.
- Measuring the old radiator instead of the pipe centres and the distance from the floor to the pipes.
- Forgetting that a taller radiator rises upwards on existing pipes, and then finding it touches the sill or shelf.
- Leaving too little space above for airflow, or hanging long curtains over the radiator.
- Comparing output without using the same ΔT, so two radiators look closer or further apart than they are.
- Using a Type 22 where the wall distance of the pipes is too small for the deeper panel.
When is 700 mm the right height?
Choose 700 mm when you want more output without more width, and your sill or shelf leaves enough space. If a 600 mm radiator is almost enough, a 700 mm one in the same width may be the simplest swap, as the pipe centres stay the same. If output is the main issue, also compare a Type 22 at 600 mm, which may suit a low sill better.
How does a taller radiator change the fit on existing pipes?
The pipes and valves fix the position of the bottom of the radiator. A taller radiator therefore rises upwards. Check the top edge against the windowsill, shelf or any socket above. The pipe centre width is not affected by height, so your width calculation from the main page still applies.
How much space should be left around it?
Leave room below for the valves and for air to circulate, and room above for the top grille and for heat to rise. The exact minimum gaps differ by maker, so use the figures in the installation instructions. A radiator that sits too close to a sill or is covered by a long curtain gives less useful heat.
How do I compare output between sizes?
Use the maker's output table for the exact model, panel type, height and width. Compare at the same ΔT, normally ΔT50 in the UK. If you run a lower flow temperature, for example with a heat pump, the real output is lower than the ΔT50 figure, so ask an installer to size the room. We do not give heat loss figures here.
Is 700 mm a metric size that matches an old radiator?
700 mm is about 27.6 in. Old imperial radiators were built to different sizes, so a metric 700 mm will rarely match exactly. Measure the old radiator and the pipes, and compare with the new drawing rather than assuming a like-for-like match.
FAQ
What are the standard radiator heights in the UK?
Common heights are 300, 400, 500, 600, 700 and 900 mm, and some makers also offer 450 mm. Not every maker offers every height in every width and panel type, so check the range you want.
Is a 700 mm radiator better than a 600 mm one?
It is not better in every case. It gives more output for the same width and type, but needs more vertical space. It is a good option where the width is fixed and the sill is high enough.
Can I replace a 600 mm radiator with a 700 mm one on the same pipes?
Often yes, if the width and pipe centres match and there is room above. The pipes set the bottom of the radiator, so check the top edge against the sill. Also check the wall distance for the panel type.
Does the 700 mm height include the top grille?
Makers normally quote the overall height of the radiator. Check the dimensions on the drawing for the exact model, including any grille or bracket details.
What width should I choose at 700 mm?
Work out the maximum body width from your pipe centres and valve allowance, then choose the next standard width down if you are between sizes. Close the gap with extension tails.
Will a 700 mm radiator heat my room?
That depends on the heat loss of the room and your flow temperature. Compare the maker's output table with a heat loss figure from an installer or a proper calculation. This page does not size heating.
More guides
- Radiator pipe centres size guide UK: how to measure and match
- How to Measure Radiator Pipe Centres
- Radiator wall distance: how to measure it and what to do with the number
- Radiator valve spacing check for UK replacements
- Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
- Standard radiator sizes in the UK: heights, widths and panel types
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 400mm high radiators in the UK: which width and type fits