Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
A double panel radiator has two water panels, one behind the other. In the UK that means Type 21 (P+) or Type 22 (K2). Both give more output than a single panel in the same height and width, but they stand further off the wall and weigh more. This page covers the sizes you will see, how depth changes what fits, and how to pick a height and width for a swap. Always confirm the exact figures on the maker's data sheet before you order.
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Our picks
Type 22 double panel double convector radiator, 600 mm high
Gives the most output for a given width and height among common panel radiators. Check the data sheet for depth, tapping positions and output at Delta T 50.
View on AmazonAdType 21 double panel single convector radiator
Slightly shallower than a Type 22. Useful when depth or pipe position rules out a K2.
View on AmazonAdSolid chrome radiator extension tails, 1/2 in BSP
Closes the gap per side without moving pipework. Choose the length from your own measurement.
View on AmazonAdAngled TRV and lockshield valve set, 15 mm
A fresh set avoids leaks at old valve seats. Check that the pipe comes up from the floor, not out of the wall.
View on AmazonAdRadiator wall brackets, heavy duty
A filled double panel is heavy. Use brackets rated for the weight and fix into solid wall or studs as the maker advises.
View on AmazonAdCommon buying mistakes
- Ordering by height and width alone and ignoring the tapping positions on the data sheet.
- Forgetting the depth of a Type 22 against a window sill or a door swing.
- Using the old radiator's output as the size guide without checking the new one at Delta T 50.
- Choosing a body width that leaves no room for valves and tails.
- Hanging a filled double panel on light brackets or weak plasterboard fixings.
- Blocking the air flow under or above the radiator with a tight sill, a shelf or a curtain.
What is the difference between Type 21 and Type 22?
Both have two water panels. Type 21 (P+) has one convector fin set between or behind them. Type 22 (K2) has two. The Type 22 gives more output for the same height and width and sits further out from the wall. If a Type 22 does not fit your depth, a Type 21 is the step down.
How deep is a double panel radiator?
A Type 22 is typically around 100 mm deep for the radiator body. The valve, tails and any bracket spacing add to what you see in the room. The data sheet from the maker is the only reliable figure, because depth differs between ranges.
Can I go from a Type 11 to a Type 22 in the same space?
Often yes for width and height, but check three things. The extra depth must clear the sill and furniture. The wall to pipe centre must suit the new panel. The wall fixings must carry more weight. If the pipes sit close to the wall, angled valves or tails may need a change.
How do I choose the width?
Start with the pipe centres. Subtract valve and tail allowance on each side, then choose the next standard width down. Close the remaining gap per side with extension tails. If you need more output, increase the height before you try to stretch the width.
What output should I look for?
UK makers quote output at Delta T 50 in watts or BTU/h. Compare like with like at that figure. This page does not size a room. Use a proper heat loss calculation or ask a heating engineer if you are changing the output.
FAQ
Is a Type 22 the same as a K2?
Yes. K2 is the common trade name for a double panel radiator with double convector fins, which is Type 22.
Which standard heights are common for double panel radiators in the UK?
Many ranges offer 300, 400, 450, 500, 600 and 700 mm, and some also offer 900 mm. Not every range has every height, so check the maker's list.
Can a double panel radiator replace a single panel of the same width?
Usually yes for width and height. Check depth, wall to pipe centre and the bracket position. You will also get more output, so make sure that is what you want.
Do I need to drain the system to swap a radiator?
For a like for like swap you normally isolate the radiator with the valves and drain only that radiator. If the valves do not shut off fully, you may need to drain more of the system. Ask a heating engineer if unsure.
Are double panel radiators heavier than single panel?
Yes, noticeably, especially when full of water. Use brackets rated for the weight and fix into solid wall or studs as the maker advises.
More guides
- Radiator pipe centres size guide UK: how to measure and match
- How to Measure Radiator Pipe Centres
- Radiator wall distance: how to measure it and what to do with the number
- Radiator valve spacing check for UK replacements
- Standard radiator sizes in the UK: heights, widths and panel types
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 700mm high radiators in the UK: widths, clearances and fit
- 400mm high radiators in the UK: which width and type fits