Radiator valve spacing check for UK replacements
Most failed radiator swaps come down to one number: the distance between the two valves. This page shows how to measure that spacing, compare it with the new radiator's tapping centres, and decide whether the pipes will reach. It adds to the main size check and does not repeat it. We cover measuring and choosing parts, not boiler or gas work. If you are not comfortable draining the system, ask a plumber.
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Our picks
Solid chrome radiator extension tails, 1/2 in BSP
Solid tails can be cut to length, so one pair covers several gaps. Check the thread is 1/2 in BSP before you cut.
View on AmazonAdTelescopic radiator valve extension
Adjustable length makes small mismatches easier to handle. Fit it only where the maker allows it, and make sure it sits fully tight.
View on AmazonAdAngled TRV and lockshield set, 15 mm
A fresh pair avoids reusing old seals and gives you a known valve centre for your measurement.
View on AmazonAdCorner radiator valve pair, 15 mm
Corner valves turn the connection through a different angle, so a pipe in the wall can reach a bottom tapping.
View on AmazonAdRadiator valve tail and nut set, 1/2 in BSP
Fresh tails and nuts give a clean seat and make the connection easier to seal.
View on AmazonAdThread sealing cord or PTFE tape for radiator tails
Needed for the threaded joints. Use sealing cord or PTFE tape as the valve maker advises.
View on AmazonAdCommon buying mistakes
- Measuring from the radiator's overall length instead of the valve centres.
- Using the old radiator's tapping centres as the new valve spacing without checking the maker's drawing.
- Ignoring which way the tapping faces, so the tails add height instead of width.
- Forcing the radiator onto pipes that are out of line, which strains joints and invites leaks.
- Measuring only one side and assuming the other pipe sits at the same height and wall distance.
- Cutting solid tails before the new radiator is on the brackets and the final gap is known.
How do I measure valve spacing correctly?
Switch the heating off and let the radiator cool. Measure from the centre of one valve tail nut to the centre of the other, in mm, with a steel tape. Then measure the height from the floor to the pipe centre on each side, and the distance from the wall to the pipe centre. Write the three numbers down before you drain anything. Take the measurements again after the old radiator is off, because valves can sit slightly out of line.
What is the difference between valve spacing and tapping centres?
Valve spacing is what your pipes give you. Tapping centres are what the radiator gives you. They only match on a true like-for-like swap. Overall radiator length is a poor guide, because the tapping position varies by maker and model. Take the figure from the technical drawing of the exact model and length.
When do extension tails help?
A tail adds distance along its own axis. On a radiator with side tappings, that closes a lengthways gap. On a radiator with bottom tappings, the tail usually points up, so it adds height and does not close a sideways gap. Check which way your tails will point before you buy them.
When do corner valves make sense?
Use them when the pipe leaves the wall below or beside the radiator and an angled valve would point the wrong way. They also help where a straight valve would push the radiator too far from the wall. Check the wall distance again with the new valve in place.
How much can I bend or ease the pipes?
Only a little. Copper pipe can take small adjustments, but forcing a joint can cause leaks later. As a rule, if you have to push hard to line things up, stop and choose a different radiator width or change the pipework. If you are unsure, ask a plumber for a quick look.
Should I replace the valves while I am there?
Often yes, if the valves are old, stiff or weeping. New valves also remove one unknown from your measurement. Make sure they suit your 15 mm pipe and fit with the same type of compression joint. The system has to be drained for this anyway.
FAQ
How far apart should radiator valves be?
They should match the tapping centres of the radiator you are fitting, within the small tolerance the pipework can absorb. The exact figure comes from the maker's drawing for that model and length.
Can I move radiator pipes closer together?
Yes, but it is plumbing work. It means draining the system and altering the pipes. If you only need to close a small gap on a side tapping radiator, extension tails may be enough.
Do extension tails reduce heat output?
We have no reliable figures for that, so we do not make a claim. For heat output, use the maker's data for the radiator itself.
What if my pipes are different heights?
Fix one pipe so both sit at the same height. A radiator hung out of level or under strain is not a good result, and a small level difference can also affect bleeding.
Can I do this myself?
Many people replace a radiator on existing pipes. You must drain the system, take care with sealing and refill and bleed afterwards. Work on the boiler or gas supply is separate and needs a Gas Safe registered engineer.
More guides
- Radiator pipe centres size guide UK: how to measure and match
- How to Measure Radiator Pipe Centres
- Radiator wall distance: how to measure it and what to do with the number
- Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
- Standard radiator sizes in the UK: heights, widths and panel types
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 700mm high radiators in the UK: widths, clearances and fit
- 400mm high radiators in the UK: which width and type fits