Radiator pipe centres size guide UK: how to measure and match
Pipe centres are the distance between the middle of one pipe and the middle of the other where they meet the radiator. This page shows you how to measure them, how to turn the result into a gap per side when you choose a different width, and which fix suits which gap. It uses millimetres and the standard UK widths. It does not cover heat output or gas work. If you need to drain the system and aren't confident doing it, ask a heating engineer.
As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Our picks
Solid chrome radiator extension tails, 1/2 in BSP
Solid tails are stiffer than flexible hose and can be cut to length. Buy two, one per side, and measure the gap first.
View on AmazonAdTelescopic radiator valve extension
The length adjusts, so a few millimetres of error don't matter. Check the stated min and max length against your gap.
View on AmazonAdAngled radiator valve pair, 15 mm
A matched TRV and lockshield pair means you don't mix old and new unions. Check the pipe size is 15 mm.
View on AmazonAdCorner radiator valve pair, 15 mm
The valve turns the connection through 90 degrees, so it lines up with pipes in the wall.
View on AmazonAdMyson Premier HE Imperial panel radiator
The range is made in sizes meant to match old imperial pipe spacing. Confirm the exact size against your pipe centres before ordering.
View on AmazonAdThread sealing cord or PTFE tape for radiator tails
You need a sealant on every threaded joint. Use one that is suitable for heating water.
View on AmazonAdCommon buying mistakes
- Measuring from the valve body instead of the middle of the pipe.
- Measuring only once, or only at one height.
- Ordering a wider radiator and expecting tails to make it fit.
- Assuming two radiators of the same width have the same tapping position. Check the drawing.
- Mixing inches and millimetres. 1 in is 25.4 mm.
- Using the full width difference as the gap per side. Divide it by 2.
How do I measure pipe centres correctly?
Use a steel tape. Measure from the middle of one pipe to the middle of the other, at the height of the valve connection. If the old radiator is still on the wall, measure on the pipes below the valves. If the pipes are not parallel, measure at both the floor and the valve height and write both figures down. A difference of more than a few millimetres means the pipes will need to be bent or the new valves will be under strain.
Is pipe centres the same as radiator width?
No. The radiator body is wider than the pipe centres, because the tappings sit in from each end and the valves add their own reach. That is why the rule on this page uses the old radiator as the reference. If the new radiator is 100 mm narrower than the old one and uses the same valves, each side needs about 50 mm more reach. Many listings give only the width, so look for the product drawing when the figure matters.
Which standard widths should I consider?
Start with the width of the old radiator. If it's not available, go to the next width down and close the gap with tails. Going down one 100 mm step creates about 50 mm per side. Going down two steps creates about 100 mm per side, which is the upper end for tails. Heat output drops as the radiator gets smaller, so check the room's needs before you go down a size.
Can I fit a wider radiator on the same pipes?
Not without moving the pipes. A wider radiator has its tappings further apart than your pipes. Tails can only add reach toward the radiator, not take it away. If you need a larger radiator, ask a plumber to move the pipes, or choose a taller radiator of the same width instead.
What if the pipes don't match the wall distance either?
Pipe centres only tell you the left to right fit. The wall distance is a separate check, and the main guide covers it by panel type. Do both measurements before you order. A radiator that fits across but sits too far from the wall will put the pipe under strain or leave the valve out of line.
When is it cheaper to move the pipes?
When the gap per side is well over 100 mm, or when you want a wider radiator, or when the pipes are uneven. Long tails look untidy and can flex. A plumber can often alter the pipes while the system is drained for the swap, which costs less than a second visit.
FAQ
What are standard radiator pipe centres in the UK?
There is no single figure. Pipe centres depend on the radiator width, the valves and the maker. Measure your own pipes, then compare with the maker's drawing for the new radiator.
How much narrower can the new radiator be?
Up to about 100 mm per side is common for solid extension tails. That means a radiator up to about 200 mm narrower than the old one. Beyond that, change the width or move the pipes.
Do I need to drain the system to measure?
No. You can measure the pipes with the old radiator in place. You do need to drain the radiator or system before you fit new valves or tails.
Are metric radiators a good match for old imperial pipework?
Sometimes not. Imperial sizes do not line up with 100 mm steps. A small gap can be closed with tails, but a large one cannot. Imperial-sized ranges such as Myson Premier HE Imperial exist for this case.
Does height affect pipe centres?
Not directly. Pipe centres are the left to right distance. Height changes how far the pipes sit from the floor. If you swap a 600 mm high radiator for a 500 mm one, check the valve and pipe position as well.
Can I cut the pipes to fit?
Altering pipework is a plumbing job. If the gap is too big for tails, a plumber can move the pipes. This page only covers measuring and choosing parts.
More guides
- How to Measure Radiator Pipe Centres
- Radiator wall distance: how to measure it and what to do with the number
- Radiator valve spacing check for UK replacements
- Double panel radiator sizes UK: Type 21 and Type 22 height, width and depth
- Standard radiator sizes in the UK: heights, widths and panel types
- 600mm high radiators in the UK: widths, panel types and what fits your wall
- 700mm high radiators in the UK: widths, clearances and fit
- 400mm high radiators in the UK: which width and type fits